when J leave my computer for about 15-20 minutes it freezes..and before leaving it,everything is ok..J have kaspersky and several simular programmes(ccleaner,tune up..) do you know where the problem is?
pedjaaaa 0 Newbie Poster
Bob_180_Bob 41 Posting Virtuoso
In your PC?? Sorry about that!!
You have given very little information, you could try the following:-
A lot of problems can be fixed with a simple solution, please try to one or, if necessary, all of the following to try and get your PC working again. Start at the first, working your way to the last, that is, if you are able to access the programs shown. If you know your way around a PC, I am sorry for the full details but this is to help people that don’t know how.
Check Disk
1. Right click your disk drive icon (normally “C”),
2. Click “Properties.”
3. Click “Tools”
4. In “Error checking” click “Check Now”
5. Check the 2 boxes, “Automatically fix file system errors” and “Scan for and attempt recovery of bad sectors”
6. Click “Start”
7. At the pop-up window “The disk check could not……” Click “Yes”
8. Re-boot your PC and allow disk checker to start. (Do not press any key before it starts)
Check Disk from Boot
1. Re-boot PC, after the single “Beep” tap F8 several times until the windows boot window appears.
2. Scroll to “Safe Mode with command prompt”
3. At command prompt Type “ chkdsk /f” (Note;- Space after chkdsk.)
Alternative Start Mode
1. Re-boot PC, after the single “Beep” tap F8 several times until the windows boot window appears.
2. Scroll to “Start with last known good configuration.)
3. Press “Enter”
Or
4. Re-boot PC, after the single “Beep” tap F8 several times until the windows boot window appears.
5. Scroll to “Safe Mode” (With networking, if you want to access the internet)
6. Press “Enter”
Verify Window’s Files
1. Go “START”, “RUN” type “CMD” Press “OK” or Boot PC into “safe mode with command prompt”
2. Type sfc /scannow /f (note:- space after sfc)
3. Windows file protection will check your files. Follow any prompts; you may be required to use your XP CD.
4. Re-boot your PC
System Restore from boot
1. Re-boot PC, after the single “Beep” tap F8 several times until the windows boot window appears.
2. Scroll to “Safe Mode” and press “Enter”
3. A window will open asking if you want to use “System Restore”
4. Select “Cancel” to enter “System Restore”
5. Ensure “Restore to an earlier time” is checked and click “Next”
6. Select an earlier date when your PC worked well. (Must be a highlighted date)
7. Click “Next”
8. Allow system restore and reboot.
9. Check to see if problem still exists.
System Restore
1. Go “Start”
2. “All programs”
3. “Accessories”
4. “System tools”
5. “System Restore”
6. Ensure “Restore to an earlier time” is checked and click “Next”
7. Select an earlier date when your PC worked well. (Must be a highlighted date)
8. Click “Next”
9. Allow system restore and reboot.
10. Check to see if problem still exists.
Clean Boot
1. Go “Start”
2. “Run”
3. Type “msconfig”
4. Click “OK”
5. Click “Services”
6. Check box “Hide all Microsoft services”
7. Click “Disable All”
8. Click “Apply”
9. Click “Restart”
10. System will reboot, Check if problem still exists. (Do not access the internet or open any file you are unsure of as you have no virus protector running.)
11. If problem is fixed, enable the disabled items 1 at a time until you find the one causing the problem. If not fixed, re-enable all and re-boot.
On-line Virus Scan
Go to one or all of these sites and do an online virus scan.
us.mcafee.com/root/mfs/default.asp
Check Malware
Go to http://www.besttechie.net/tools/mbam-setup.exe
and download and run Malwarebytes' Anti-Malware.
Check Spyware
Go to www.safer-networking.org and download and run Spybot
If you have not installed Service Pack 3 yet, do a Windows repair, if you have installed it, first try…..
Post a detailed report
Go to:- www.majorgeeks.com/download3155.html download and run Hijack this. “Do not try to do any repairs yourself.” Save the report and send it with your next post along with any error logs.
To check error logs, go to “START” “RUN” type “eventvwr.msc” Click “OK” and check if there any errors in the logs. Include any information that could help:-
1. What were you doing on the PC when the problem occurred?
2. Does it happen every time you do this?
3. What progs are running as well?
4. What have you done to fix this problem?
5. How long has the problem been happening?
6. Have you installed/uninstalled or updated any progs recently?
7. Any other information that may help resolve your problem. Remember, no one here can see your PC; you are the only one that can tell someone else about the problem.
To Repair Windows XP from your XP CD…..
1. Re-start PC with XP CD in drive (Have your serial number handy)
2. As your PC starts press “F12” for boot menu (Or what your PC may ask for)
3. Scroll to and select “boot from CD.”
4. At prompt “Press any key to boot from CD” Press “Any key”
5. In the Windows XP Setup window, Press “Enter” to set up windows XP, (Don’t worry, this is a repair only, not a fresh install.)
6. At next window, Press “F8” to accept license agreement
7. Wait until windows displays your current version of XP and asks “To repair the selected windows XP installation press R”
8. Press “R”
9. Enter serial number when prompted.
10. Wait for files to be copied (PC will indicate 39 mins, it will take a lot less.)
11. When asked to adjust Regional language options, click “Next” as it is still set.
12. PC will re-boot.
13. If you have AVG Free, copy serial number to a file as you will lose it on repair. After repair a window will pop up asking how you want to treat AVG, Click repair and when prompted enter serial number.
14. Check to see if problem still exists.
sittas87 91 Nearly a Posting Virtuoso
Hi
Check you're CPU temperature in you're BIOS. I have a strong feeling thats its you're CPU temperature thats too high. A normal temp in BIOS is accepted if its below 60, I recommend below 65 degrees. Alternatively blow out you're pc with can air to remove all dust and apply thermal grease on you're CPU.
roz33 0 Newbie Poster
ok i seem to have same problem with freezing of pc, i hear a whirring noise, like a fan i suppose which last about a minute or more, during which time pages load so slow, other issues i am having is once pc is loaded after its turned on, i get (1)"nwiz.exe has to close" type error, (2) i cannot use the netdignostics in tools because "framedyn.dll is missing" error,
(3)i cannot install DAZ Studio 3d program anymore because it keeps saying its configured wrong re-installing may fix problem but it dont!, i had it working b4. i have Aviria Antivirus running,b4 i had Avast,but switched. i think i maybe missing or have currupt XP files,but no longer have XP disc, dont want to do destructive dump again and replace all files, just installed a new harddrive April this year. here are my spec,tell me what to do if ya see an issue.
OS Name Microsoft Windows XP Home Edition
Version 5.1.2600 Service Pack 2 Build 2600
OS Manufacturer Microsoft Corporation
System Name Private
System Manufacturer Compaq Presario 06
System Model DA236A-ABA 6420NX NA910
System Type X86-based PC
Processor x86 Family 6 Model 8 Stepping 0 AuthenticAMD ~1798 Mhz
BIOS Version/Date Phoenix Technologies, LTD 3.01, 12/10/2002
SMBIOS Version 2.2
Windows Directory C:\windows
System Directory C:\windows\system32
Boot Device \Device\HarddiskVolume1
Locale United States
Hardware Abstraction Layer Version = "5.1.2600.2180 (xpsp_sp2_rtm.040803-2158)"
User Name Private
Time Zone Central Daylight Time
Total Physical Memory 256.00 MB
Available Physical Memory 82.93 MB
Total Virtual Memory 2.00 GB
Available Virtual Memory 1.96 GB
Page File Space 1.35 GB
Page File C:\pagefile.sys
roz33 0 Newbie Poster
ok i seem to have same problem with freezing of pc, i hear a whirring noise, like a fan i suppose which last about a minute or more, during which time pages load so slow, other issues i am having is once pc is loaded after its turned on, i get (1)"nwiz.exe has to close" type error, (2) i cannot use the netdignostics in tools because "framedyn.dll is missing" error,
(3)i cannot install DAZ Studio 3d program anymore because it keeps saying its configured wrong re-installing may fix problem but it dont!, i had it working b4. i have Aviria Antivirus running,b4 i had Avast,but switched. i think i maybe missing or have currupt XP files,but no longer have XP disc, dont want to do destructive dump again and replace all files, just installed a new harddrive April this year. here are my spec,tell me what to do if ya see an issue.
OS Name Microsoft Windows XP Home Edition
Version 5.1.2600 Service Pack 2 Build 2600
OS Manufacturer Microsoft Corporation
System Name Private
System Manufacturer Compaq Presario 06
System Model DA236A-ABA 6420NX NA910
System Type X86-based PC
Processor x86 Family 6 Model 8 Stepping 0 AuthenticAMD ~1798 Mhz
BIOS Version/Date Phoenix Technologies, LTD 3.01, 12/10/2002
SMBIOS Version 2.2
Windows Directory C:\windows
System Directory C:\windows\system32
Boot Device \Device\HarddiskVolume1
Locale United States
Hardware Abstraction Layer Version = "5.1.2600.2180 (xpsp_sp2_rtm.040803-2158)"
User Name Private
Time Zone Central Daylight Time
Total Physical Memory 256.00 MB
Available Physical Memory 82.93 MB
Total Virtual Memory 2.00 GB
Available Virtual Memory 1.96 GB
Page File Space 1.35 GB
Page File C:\pagefile.sys
Bob_180_Bob 41 Posting Virtuoso
Roz33, Please start your own thread. Try the easy fixes I have detailed above and if they don't work:-
Post a detailed report
Go to:- www.majorgeeks.com/download3155.html download and run Hijack this. “Do not try to do any repairs yourself.” Save the report and send it with your next post along with any error logs.
To check error logs, go to “START” “RUN” type “eventvwr.msc” Click “OK” and check if there any errors in the logs. Include any information that could help:-
1. What were you doing on the PC when the problem occurred?
2. Does it happen every time you do this?
3. What progs are running as well?
4. What have you done to fix this problem?
5. How long has the problem been happening?
6. Have you installed/uninstalled or updated any progs recently?
7. Any other information that may help resolve your problem. Remember, no one here can see your PC; you are the only one that can tell someone else about the problem.
Be a part of the DaniWeb community
We're a friendly, industry-focused community of developers, IT pros, digital marketers, and technology enthusiasts meeting, networking, learning, and sharing knowledge.